8BitFlux Binary Keyboard
ਨਿਰਧਾਰਨ
- Part Standoffs:
- M3 nylon stands 8 mm – Qty: 4
- M3 nylon stands 12 mm – Qty: 2
- Pin header: 2 x 2 pin male horizontal (backside)
- Pin header: 2 x 5 pin male horizontal (backside)
- Resistor: 270 1/4 W – red, violet, black, black, brown
(ਪਿੱਛੇ) - Switches: DPDT Small slide Switch ON-ON, SPDT Big slide switch
ਆਨ-ਆਨ - LED: Yellow 3 mm, round
- ਕੁੱਲ ਹਿੱਸੇ: 23
- Total Types: 9
ਭਾਗਾਂ ਦਾ ਵਰਣਨ
| ਭਾਗ | ਮੁੱਲ | ਟਿੱਪਣੀਆਂ | ਮਾਤਰਾ | ਹਵਾਲਾ | ਪ੍ਰਦਾਨ ਕੀਤਾ |
| Standoffs | M3 | nylon stands 8 mm | 4 | ||
| M3 | nylon stands 12 mm | 2 | |||
| M3 | nylon nuts | 4 | |||
| ਸਿਰਲੇਖ ਨੂੰ ਪਿੰਨ ਕਰੋ | 2 x 2 ਪਿੰਨ | ਮਰਦ ਹਰੀਜੱਟਲ (ਪਿੱਛੇ) | 1 | J1 | |
| 2 x 5 ਪਿੰਨ | ਮਰਦ ਹਰੀਜੱਟਲ (ਪਿੱਛੇ) | 1 | J2 | ||
| ਰੋਧਕ | 270 Ω | 1/4 W – red, violet, black, black, brown (ਪਿੱਛੇ) | 1 | R1 | |
| ਸਵਿੱਚ ਕਰੋ | ਡੀ.ਪੀ.ਡੀ.ਟੀ | Small slide Switch ON-ON | 1 | SW9 | |
| ਐਸ.ਪੀ.ਡੀ.ਟੀ | Big slide switch ON-ON | 8 | SW1-SW8 | ||
| LED | ਪੀਲਾ | 3 ਮਿਲੀਮੀਟਰ, ਗੋਲ | 1 | D1 | |
| ਹਿੱਸੇ | 23 | ||||
| ਕਿਸਮਾਂ | 9 |
ਅਸੈਂਬਲੀ ਨਿਰਦੇਸ਼
- Mount the standoffs first. The long ones (12 mm) screw in the short (8 mm) at the top edge of the main (bottom) board. Use two of the four nuts to mount the short standoffs at the bottom edge of the board.
- If a finished 8-bit Workbench is available, insert the unsoldered pin headers (J1, J2) into the female busses of the Workbench to have them perfectly aligned before soldering them.
- Solder the small slide switch (SW9) and the resistor (R1, insert at the bottom side, solder at the top).
- Remove all nuts and rings from the eight switches, leave one nut on and turn it all the way down. Then, put the switches in and make sure they all are oriented the same way (i.e. the notch in the threading points to the bottom edge of the board). Do not solder them in yet.
- Put on the front panel and tighten the remaining two black nuts securely on the long standoffs.
- Use a small flat screwdriver (like a watchmaker screwdriver) to tighten the nut of the switches. They move upwards so they touch the front panel at the bottom side. Make sure the front panel stays horizontal, do not tighten them too much.
- Screw on another nut (one per switch, without rings) at the top side and tighten firmly by hand.
- When everything is solid and without slack, solder the eight big switches in. A bigger solder head is recommended for better solder flow.
- Finish with soldering the LED (D1). Keep the legs long, they go through the front panel and the main board at the bottom. Start soldering them on the bottom board. The long leg is the anode (+) and the short leg the cathode (-). The short leg goes through the square pad.
Before applying power, check J1 and J2 for shorts between all side-to-side pins using a multimeter in continuity mode. Happy toggling!
ਅਕਸਰ ਪੁੱਛੇ ਜਾਂਦੇ ਸਵਾਲ
Q: How do I ensure proper alignment of pin headers J1 and J2?
A: Insert the unsoldered pin headers into the female busses of the Workbench to align them perfectly before soldering.
Q: What is the orientation of the switches when installing them?
A: Make sure the notch in the threading points to the bottom edge of the board for proper orientation.
ਦਸਤਾਵੇਜ਼ / ਸਰੋਤ
 |
8BitFlux Binary Keyboard [pdf] ਹਦਾਇਤ ਮੈਨੂਅਲ Binary Keyboard, Binary, Keyboard |