FlySpark-logo

FlySpark F4 V1 Stack Flight Controller

FlySpark-F4-V1-Stack-Flight-Controller-productਨਿਰਧਾਰਨ

  • ਉਤਪਾਦ ਦਾ ਨਾਮ:
    FlySpark F4 V1 BLS 60A Stack
  • AI ਵਿਸ਼ੇਸ਼ਤਾਵਾਂ:
    Sensor Fusion, PID Autotuning, Adaptive Filtering
  • ਸਾੱਫਟਵੇਅਰ ਸਹਾਇਤਾ:
    Betaflight, INAV, Ardupilot, EMU-flight, SkyBrush
  • ESC Communication:
    BLHeli_S Bluetooth & USB-C
  • ਕਨੈਕਟੀਵਿਟੀ:
    3-6S ਲੀਪੋ
  • ਮਾਪ:
    47.8mm(L) x 47.5mm(W) x 18.3mm(H)
  • ਮਾਊਂਟਿੰਗ:
    30.5mm ਮੋਰੀ ਆਕਾਰ ਦੇ ਨਾਲ 30.5 x 4mm
  • ਭਾਰ:
    34 ਗ੍ਰਾਮ

FlySpark-F4-V1-Stack-Flight-Controller-fig-9 FlySpark-F4-V1-Stack-Flight-Controller-fig-10

ਉਤਪਾਦ ਵਰਤੋਂ ਨਿਰਦੇਸ਼

FlySpark F4 V1 Flight Controller

ਖਾਕਾ:
Refer to the user manual for the layout of the flight controller.

ਪੈਰੀਫਿਰਲ ਕਨੈਕਸ਼ਨ:
Connect peripherals as per the provided diagram.

App & FC Configuration:
Use the recommended apps and follow the configuration instructions.

FC Firmware Update:
Connect the flight controller to a PC via USB for firmware updates.

FLYSPARK BLS 60A 4-IN-1 ESC

ਖਾਕਾ:
Check the layout guide in the manual for proper installation.

ਮੋਟਰਾਂ ਅਤੇ ਪਾਵਰ ਕੇਬਲ ਨਾਲ ਕਨੈਕਸ਼ਨ:
Connect motors and power cables securely.

ESC Configuration:
Use the FlySpark app for ESC configuration settings.

ESC Firmware Update:
Follow the provided steps to update the firmware for ESC.

FlySpark F4 V1 BLS 60A StackFlySpark-F4-V1-Stack-Flight-Controller-fig-1

ਸਪੈਕਸ ਓਵਰviewFlySpark-F4-V1-Stack-Flight-Controller-fig-20

FlySpark-F4-V1-Stack-Flight-Controller-fig-2 FlySpark-F4-V1-Stack-Flight-Controller-fig-3

ਪੈਕੇਜFlySpark-F4-V1-Stack-Flight-Controller-fig-4.1

  • FlySpark F4 V1 Flight Controller x 1
  • FlySpark BLS 60A 4-in-1 ESC x 1
  • 35V 1000uF ਘੱਟ ESR ਕੈਪਸੀਟਰ x 1
  • M3 ਨਾਈਲੋਨ ਨਟ x 4
  • SH 1.0mm 25mm-ਲੰਬਾਈ 8pin ਕੇਬਲ (FC-ESC ਕਨੈਕਸ਼ਨ ਲਈ) x 1 SH 1.0mm 75mm-ਲੰਬਾਈ 6pin ਕੇਬਲ* x 1
  • M3*30mm ਅੰਦਰੂਨੀ-ਹੈਕਸਾਗਨ ਸਕ੍ਰਿਊਜ਼ x 4
  • DJI 6pin ਕੇਬਲ(80mm) x 1
  • XT60 ਪਾਵਰ ਕੇਬਲ (100mm) x 1

FlySpark-F4-V1-Stack-Flight-Controller-fig-5.2

FC Connection diagramFlySpark-F4-V1-Stack-Flight-Controller-fig-6

Guide to FC & ESC Connections

ਢੰਗ 1:

  • Using 8.Pin JST CableFlySpark-F4-V1-Stack-Flight-Controller-fig-7

ਢੰਗ 2:

ਡਾਇਰੈਕਟ ਸੋਲਡਰਿੰਗ

  • Solder 8 wires to the 8 pads on each end, following the pad definitions belowFlySpark-F4-V1-Stack-Flight-Controller-fig-8

Flight controller specs

FlySpark-F4-V1-Stack-Flight-Controller-fig-11.2

  • O6 ਏਅਰ ਯੂਨਿਟ ਦੇ ਨਾਲ ਆਉਂਦੀ 3-ਪਿੰਨ ਕੇਬਲ ਦੀ ਵਰਤੋਂ ਕਰੋ FlySpark-F4-V1-Stack-Flight-Controller-fig-12.1
  • Use 6-pin cable comes with the FlySpark F4 V1 BLS 60A Stack

FlySpark-F4-V1-Stack-Flight-Controller-fig-13

F C Firmware  update
To update the firmware for your FlySpark F4 VI flight controller, please follow these steps:
Connect the Flight Controller to Your PC:

  • Use a USB cable to connect the FlySpark F4 VI flight controller to your PC

Open Betaflight I INAV Configurator.

  • . Launch the Betaflight Configurator or INAV Configurator on your PC. For this guide, we’ll use Betaflight Configurator as an example.

Navigate to Firmware Flashing:

  • In the Betaflight Configurator, navigate to the ‘Firmware Flashing’ page.

Select Target and Flash Firmware:

  •  Choose the target firmware for ‘Flyspark F4 VI’ from the dropdown menu.
  • Initiate the firmware flashing process.

ਨੋਟ:
The Flyspark F4 VI flight controller does not support wireless firmware flashing. It must be  performed using a USB connection to your PC.

FlySpark-F4-V1-Stack-Flight-Controller-fig-14

Flyspark BLS 60A 4-in-l ESCFlySpark-F4-V1-Stack-Flight-Controller-fig-15

ਮੋਟਰਾਂ ਅਤੇ ਪਾਵਰ ਕੇਬਲ ਨਾਲ ਕਨੈਕਸ਼ਨFlySpark-F4-V1-Stack-Flight-Controller-fig-16

ESC Specs FlySpark F4 V1 BLS 60A StackFlySpark-F4-V1-Stack-Flight-Controller-fig-17

ESC ਫਰਮਵੇਅਰ ਅੱਪਡੇਟ
This 8-bit 50A ESC comes pre-loaded with BLHeliS firmware but can also be flashed to Bluejay firmware, offering RPM filtering and Bi-directional Dshot support. Follow these steps to update the firmware:

  1. Prepare Your Drone:
    Remove all propellers from your drone for safety.
  2. Connect ESC to Flight Controller:
    Ensure the flight controller is properly connected to the ESC, then power up the drone. This step ensures the ESC initializes correctly.
  3. ਪੀਸੀ ਨਾਲ ਜੁੜੋ:
    Use a USB Type-C cable to connect the flight controller to your computer.
  4. Access Firmware Configuration:
    Open the Chrome browser and visit: www.esc-configurator.com
  5. Flashing Steps:
    Follow the firmware flashing steps displayed on the configurator website. Ensure you select the appropriate options for flashing to Bluejay firmware.

FlySpark-F4-V1-Stack-Flight-Controller-fig-21

ਸਾਵਧਾਨ:FlySpark-F4-V1-Stack-Flight-Controller-fig-19

  • PROPELLERS OFF: REMOVE ALL PROPELLERS.
  • SECURE CONNECTION: ENSURE SECURE ESC CONNECTION.
  • FOLLOW STEPS: FOLLOW FLASHING INSTRUCTIONS CAREFULLY.
  • STABLE POWER: ENSURE STABLE POWER SUPPLY.
  • www.FlySpark.in

ਅਕਸਰ ਪੁੱਛੇ ਜਾਂਦੇ ਸਵਾਲ

ਮੈਂ ESC ਫਰਮਵੇਅਰ ਨੂੰ ਕਿਵੇਂ ਅੱਪਡੇਟ ਕਰਾਂ?

To update the ESC firmware, follow these steps: 1. Prepare Your Drone: Remove all propellers for safety. 2. Connect ESC to Flight Controller: Ensure proper connection to the ESC and power up.

ਦਸਤਾਵੇਜ਼ / ਸਰੋਤ

FlySpark F4 V1 Stack Flight Controller [pdf] ਯੂਜ਼ਰ ਮੈਨੂਅਲ
F4 V1, BLS 60A, F4 V1 Stack Flight Controller, F4 V1, Stack Flight Controller, Flight Controller, Controller

ਹਵਾਲੇ

ਇੱਕ ਟਿੱਪਣੀ ਛੱਡੋ

ਤੁਹਾਡਾ ਈਮੇਲ ਪਤਾ ਪ੍ਰਕਾਸ਼ਿਤ ਨਹੀਂ ਕੀਤਾ ਜਾਵੇਗਾ। ਲੋੜੀਂਦੇ ਖੇਤਰਾਂ ਨੂੰ ਚਿੰਨ੍ਹਿਤ ਕੀਤਾ ਗਿਆ ਹੈ *